- Home
- Electrical Control Gear
- Products
- Thermal Management
- Heaters
- Aluminium Foil Heaters - IP68
- Cartridge Heaters
- Cast Heaters
- Ceramic Knuckle Heaters
- Coil Heaters, Coiled Heater Bands and Nozzle Heaters
- Custom Heaters
- Drum Heaters
- Finned Air Heaters
- Flanged Heaters
- Flat Tubular Heaters
- Flexible Tubular Heaters
- Heating Cables, Crankcase Heater
- Immersion Heaters
- Mica Insulated Heaters, Mica Band Heaters, Mica Plate Heaters
- PTC Self-regulating Heating Elements
- Silicone Mat Heaters, Wire Wound, Etched Foil
- Tape Heaters
- Thick Film Heating Elements
- Tubular Heaters
- Railway Heaters & Relays
- Cable Management
- Braking Resistors
- Machine Safety
- Contact
Surge Voltage Protection - Surge Arrester Class II (C)
- PLUG-IN SURGE ARRESTER, VARTEC VVP, DVP SERIES
- VARTEC SURGE ARRESTER CLASS C, VEPG SERIES FOR SINGLE-PHASE OPERATION, 230 VAC, 1 MODUL WIDE
Surge voltage protection (PDF datasheet)Product enquiry and further information (Contact us form)
PLUG-IN SURGE ARRESTER, VARTEC VVP, DVP SERIES
- Class C, design type II, type 2, meets ÖVE-SN 60, part 4 & EN/IEC 61643
| VVP 255 Varistor |
VVP 335 Varistor |
DVP 255 2) Gas-filled surge arrester |
|
| Continuous voltage Uc | 255 VAC | 335 VAC | 255 VAC |
| Nominal discharge current nl (8/20μs) | 15 kA/20 kA | 15 kA/20 kA | 20 kA |
| Max. discharge current ml ax (8/20μs) | 30 kA/40 (30) kA | 30 kA/40 (30) kA | 40 kA |
| Protection level Up at In | ) 1,3/1.4 kV | ) 1,4 kV/1,65 kV | ) 1,2 kV |
| Response time t a | < 25 ns | < 25 ns | < 100 ns |
| Max. permissible ambient temperature | -40° C up to +80° C | ||
| Degree of protection open/installed | IP 20/40 | ||
| Max. permisible fuse: | 100 A | 100 A | |
| Max. terminal cross section | 16/25 mm2 | ||
| Auxiliary contact (optional) | 250 V AC/0,5 A, max. 1,5 mm2 | ||
| DIN-rail mountable | on both sides | ||
| Max. terminal torque | 2,5 - 3,0 Nm (main terminal) |
TIPS & TRICKS
Observe the respective national regulation for installation! E.g. ÖVE 8001-1 or IEC 60361-5-53 A1. The neutral contactor does not require a surge protection device (in accordance with the TN-C switching arrangement) if the protective multiple earthing connection is set up where the surge protection device is integrated. The connection line to the equipotential bonding rail or PE rail should be as short as possible and without looping. All surge devices must be unplugged during insulation measurement. The VVP335 surge arrester has been designed for mains voltages of 3~400/230 V in accordance with ÖVE 8001-1. According to IEC 603645-5-53 A1, the VVP255 surge arrester is for export only.
RANGE OF APPLICATION
Plug-in surge arresters designed for indoor mounting as a means of protecting consumer appliances against lightning and transient voltage surges The surge arrester operates in any position. Terminal assignment for the mains and PE/PENconductor is freely definable.
DESCRIPTION
- ORDER NO.
C-arrester module 15 kA ÖVE VVP335
- IS010078
C-arrester module 20 kA ÖVE VVP335
- IS010079
C-arrester module 15 kA IEC VVP2551)
- IS010076
C-arrester module 20 kA IEC VVP2551)
- IS010077
N-PE surge arrester Module 20kA DVP2552)
- IS010075
Base,1-pol. for VVP
- IS010071-A
Base,1-pol. for VVP +H
- IS010069-A
Base,1-pol. for DVP
- IS010070-A
Base,1-pol. for DVP +H
- IS010068-A
Base 3+1 operation
- IS010064-A
Base 3+1 operation +H
- IS010065-A
Busbar, 3x, insulated, for TN-C system
- IS050103
Busbar, 4x, insulated, for TN-S, TT system
- IS050104
Busbar, 5x, insulated, for N arrangement
- IS050105
1) ÖVE design according to ÖVE 8001-1, section18. Must be implemented by law in Austria.
2) As specified in ÖNORM/ÖVE E8001-1, the 20kA requirement still applies to the surge arrester between Neutral and the main earthing rail (N/PE conductor). (PAS) or PE-rail, even in cases where surge protection devices were installed with greater nominal discharge currents, e.g. 15 kA or 20 kA between the external conductors and the Neutral conductor.
Surge voltage protection (PDF datasheet)Product enquiry and further information (Contact us form)
VARTEC SURGE ARRESTER CLASS C, VEPG SERIES FOR SINGLE-PHASE OPERATION, 230 VAC, 1 MODUL WIDE
- Class C, design type II, type 2, meets ÖVE 60, part 4 & EN/IEC 61643
TECHNICAL DATA
- Space saving - only 1 module wide
- Ideal for retrofits (renovating old buildings)
- D surge arrester, protection level (Up 950 V at 5 kA In (8/20)
- High back-up fuse possible
- National regulations for installation must be followed!
RANGE OF APPLICATION
Surge arresters designed for indoor mounting as a means of protecting consumer appliances against lightning and transient voltage surges The surge arrester operates in any position. The connection line to the equipotential bonding rail or PE rail should be as short as possible and without looping. When measuring insulation, the surge arrester is disconnected from PE by the gasfilled spark gap.
- VEPG
- Varistor + gas surge arrester
- Continuous voltage Uc
- 335 VAC
- Nominal discharge current
- ln (8/20μs)
- 10 kA / Pol
- Imax (8/20μs)
- 20 kA / Pol
- ln (8/20μs)
- Level of protection Up at In
- ) 1,6 kV at 5 kA 950 V
- Response time ta
- < 100 ns
- Max. permissible ambient temperature
- -40° C up to +80° C
- Degree of protection open/installed
- IP 20/40
- Max. permisible fuse:
- 100 A
- Max. terminal cross section
- L, N = 6 mm2; PE = 25/35 mm2
- Auxiliary contact (optional)
- 250 VAC / 0,5 A; max. 1,5 mm2
DESCRIPTION
- DIM. (WxHxD) mm
- ORDER NO.
C surge arrester, 10 kA, 335 V, 1-phase, 1 modul wide
- 17,5x90x65
- IS010073
Base for VMG / VEPG
- IS010201
Base + H for VMG / VEPG
- IS010202
Product enquiry and further information
We would be delighted to offer free application advice, technical information on products, free quotations and delivery information.